10.01.2019, 14:15
Das habe ich auf die Schnelle im US-Forum gefunden - es wird wohl ein anderes Ölwechselgerät benutzt was die vollständige Entlüftung und Austausch des
Öl´s sicherstellen soll.
Transmission Oil Cooler Flush Requirements Recent GM studies have shown that automatic transmission oil cooler flush requirements have limited benefit on many current transmission repairs. Based on the studies, GM will no longer require a mandatory flush and flow test of the transmission oil cooler and the oil cooler pipes — including the auxiliary transmission oil cooler, if equipped — to be performed in every instance of transmission or torque convertor replacements or internal transmission repairs. As a result of this policy change, transmission repairs will be simpler, the environmental impact of waste oil will be reduced and Global Warranty Management transaction processing will be simplified. Transmission Repair Policy Changes Effective December 1st, 2018: • Job cards will no longer require a transmission flush code from the DT-45096 Transmission Oil Cooling System Flush and Flow Test Tool (DT-45096 TransFlow® machine). • The Flush Code field in Global Warranty Management related to all applicable transmission labor operations should be left blank. The field will be eliminated mid-December. • The Warranty Support Center will no longer require a flush code on warranty transactions. Repair procedures in the Service Information will be updated to reflect the elimination of the transmission cooler flush requirement. In addition, related service bulletins, the labor time guide, and the GM Service Policies and Procedures Manual will be updated accordingly. The DT-45096 TransFlow machine continues to be a valuable GM Essential Tool that should be used when diagnosing transmission overheating conditions or a transmission failure due to a lack of lubrication. Technicians should continue to document the TransFlow code in the correction comments of the job card in instances when the DT-45096 flow test procedure is used to diagnose an overheating or lubrication concern. TIP: Use only the appropriate GM automatic transmission fluid when performing a transmission repair. If the fluid in the DT-45096 TransFlow machine is different than what is used in the transmission, after performing the flush and flow test, use compressed air to blow the residual transmission fluid out of the transmission oil cooler and lines. A new repair procedure for the DT-45096 TransFlow machine to exchange fluid also has been developed to address torque converter clutch shudder on 8L45 and 8L90 8-speed automatic transmissions (RPOs M5T, M5N, M5U, M5X). Look for more information to be released soon in a service bulletin and the December 2018 Emerging Issues seminar (10218.12V).
Wolly #108
Öl´s sicherstellen soll.
Transmission Oil Cooler Flush Requirements Recent GM studies have shown that automatic transmission oil cooler flush requirements have limited benefit on many current transmission repairs. Based on the studies, GM will no longer require a mandatory flush and flow test of the transmission oil cooler and the oil cooler pipes — including the auxiliary transmission oil cooler, if equipped — to be performed in every instance of transmission or torque convertor replacements or internal transmission repairs. As a result of this policy change, transmission repairs will be simpler, the environmental impact of waste oil will be reduced and Global Warranty Management transaction processing will be simplified. Transmission Repair Policy Changes Effective December 1st, 2018: • Job cards will no longer require a transmission flush code from the DT-45096 Transmission Oil Cooling System Flush and Flow Test Tool (DT-45096 TransFlow® machine). • The Flush Code field in Global Warranty Management related to all applicable transmission labor operations should be left blank. The field will be eliminated mid-December. • The Warranty Support Center will no longer require a flush code on warranty transactions. Repair procedures in the Service Information will be updated to reflect the elimination of the transmission cooler flush requirement. In addition, related service bulletins, the labor time guide, and the GM Service Policies and Procedures Manual will be updated accordingly. The DT-45096 TransFlow machine continues to be a valuable GM Essential Tool that should be used when diagnosing transmission overheating conditions or a transmission failure due to a lack of lubrication. Technicians should continue to document the TransFlow code in the correction comments of the job card in instances when the DT-45096 flow test procedure is used to diagnose an overheating or lubrication concern. TIP: Use only the appropriate GM automatic transmission fluid when performing a transmission repair. If the fluid in the DT-45096 TransFlow machine is different than what is used in the transmission, after performing the flush and flow test, use compressed air to blow the residual transmission fluid out of the transmission oil cooler and lines. A new repair procedure for the DT-45096 TransFlow machine to exchange fluid also has been developed to address torque converter clutch shudder on 8L45 and 8L90 8-speed automatic transmissions (RPOs M5T, M5N, M5U, M5X). Look for more information to be released soon in a service bulletin and the December 2018 Emerging Issues seminar (10218.12V).
Wolly #108